Low-performance high-efficiency sealing gasket HLelaG series
• There are three types of HLelaG gasket structure: Type I, II and III
Type I |
Type II |
Type III |
• Significant features of low-stress high-efficiency sealing gasket (HLelaG):
HLelaG can get better elastic deformation with lower pre-tightening stress: t4.5mmHLelaG can get an elastic deformation of 0.3mm under the condition of 35Mpa locking loading stress, which means that the installation is easier, and it also shows that HLelaG has enough additions Preload compression margin, so HLLaG has a longer service life.
The elastic deformation capacity of HLelaG is better than that of metal corrugated gaskets and metal spiral wound gaskets: Under the same test conditions, the elastic deformation rate (compression rate * resilience rate) of HLelaG far exceeds that of flexible graphite metal spiral wound gaskets specified in GB4622.3 The elastic deformation rate (3.06% at 70Mpa is qualified) and the elastic deformation rate of flexible graphite metal corrugated gaskets specified in GB19066.3 (3.75% at 45Mpa is qualified). Excellent elastic deformation ability ensures excellent sealing performance when working conditions change.
The sealing performance of HLelaG is better than flexible graphite metal spiral wound gasket and flexible graphite metal corrugated composite gasket.
The HLelag sealing body is a flexible body, which can better adapt to the condition of the flange sealing surface and the flange locking conditions, and the installation conditions are adaptable.
The main body of the HLelag seal is a molded and flexible whole, which will not cause the gasket to collapse and the surface non-metallic composite layer to fall off.
There are several turns of elastic alloy belt on the inner diameter side and outer diameter side of the HLelag sealing body, which protects the HLela high-elasticity, high-temperature and corrosion-resistant special flexible graphite sealing belt to ensure the sealing safety when the medium pressure increases sharply and the medium is under high pressure.
• Scope of application:
Where the outer diameter of the gasket is 800mm, such as pipeline flanges and equipment flanges within 24' of the American standard or DN600 of the European standard.
Applicable temperature -200°C ~ 650°C (oxidizing medium ≤ 450°C); applicable pressure ≤ 25Mpa.
Applicable medium: related to the selected metal material.
It still has excellent sealing performance in occasions where temperature and pressure are cycled, or where equipment or pipelines are shaken.
Optional alloy belt material table
Alloy strip material name | Jane (abbreviation) | Name of alloy strip sail | Jane (abbreviation) |
0Cr18Ni9 |
304 |
Ti |
Ti |
00Cr19Ni10 |
304L |
Ni-Cu alloy (Monel400) |
Monel |
0Cr17Ni12Mo2 |
316 |
Ni-Mo alloy (Hastelloy B2) |
HAST B |
0Cr17Ni14Mo2 |
316L |
Ni-Mo-Cr alloy (Hastelloy) C276) |
HAST C |
0Cr18Ni10Ti |
321 |
Ni-Cr-Fe alloy (Inconel 600) |
INC 600 |
0Cr18Ni11Nb |
347 |
Ni-Fe-Cr alloy (Incoloy 800) |
IN 800 |
0Cr25Ni20 |
310 |
|
|
The elastic deformation rate and nitrogen(N2 )test leakage rate under each pressure level
Final load gasket stress |
Elastic deformation rate(%) |
Leak rate(MediumN2) |
|
Medium pressure |
cm³/s |
||
35 Mpa |
6.97 |
2.55 |
2.02*10⁻⁵ |
45 Mpa |
7.49 |
2.55 |
1.59*10⁻⁵ |
68 Mpa |
8.15 |
5.0 |
3.25*10⁻⁵ |
The ammonia leakage rate detection meets the requirements of EN 14772, when the gasket test stress is 20Mpa, <2.0*10⁻⁷ cm³/s, when the gasket maximum test stress is 100Mpa, it is 1.3*10⁻⁷ cm³/s.
• Product mark description: (The inner ring material is the same as the reinforced alloy belt by default)
Type I, Type II: HLelaG type symbol-alloy belt material DN PN (flange surface type symbol)
Such as: HLelaG 1304 DN50 PN1.6 (TG), HLelaG II304 DN50 PN1.6 (MFM)
Type III: HLelaG type symbol-alloy belt material (locating ring material) DN PN (flange surface type symbol)
Such as: HLelaG III316 (304) DN50 PN1.6 (RF), HLeiaG III 316 (304) DN50 PN1.6 (FF)
Related Products
The maximum working pressure can reach 42.0MPa.
The maximum operating temperature can reach 600°C.
Maximum operating temperature: oxidizing gas: 450°C; non-oxidizing gas: 800°C.
Got Question? Call Us 24/7!
ADD:No. 1655 Chaosheng Road, Cixi Industrial Zone , Cixi City, Zhejiang,China 315318
TEL:+86-574-63013766
FAX:+86-574-63013255,63034116
E-mail:hengli@china-sealing.com
Copyright © 2020 Cixi Hengli Packing & Sealing Co., Ltd. All rights reserved.